1999-2009 [Subscribe to Daily Digest] |
Yes I cut the Nokia Mic and Speaker off and wired them into the Saab wiring harness. Don't think all ten wires are used, just these eight:
2 mic wires
2 speaker wires
1 constant power
1 switched power
1 ground
1 mute wire
The two that are not used are the illumination wire and the second mic ground wire.
Here is what Saab says: (from the Saabusa website general FAQ)
General
Are the Saab 9-5 and Saab 9-3 equipped for cellular
phones?
All 1999 SAAB models are pre-wired for power supply and
hands-free operation of cellular telephones. Depending on the
capabilities of the telephone to be installed, any, or all, of the
following features may be possible. Please note that a
hands-free kit from the phone manufacturer may be necessary
to utilize these features. Please pass this information on to your
telephone installers.
1.Auto muting of the Saab's sound system for incoming and
outgoing calls.
2.Using the audio system's speakers for hands-free calls.
3.Adjusting the telephone hands-free volume with the radio
controls, both on the radio unit and steering wheel.
4.Handset background lighting to be controlled by vehicle's
lighting controls.
5.Both constant and switched power through the vehicle's
electrical system.
In addition, 9-3 SE 5-door and all 9-5 models include a pre-wired
hands-free microphone already installed to the left of the
rear-view mirror.
WARNING: USING ANY POWER OR GROUND SOURCE
OTHER THAN WHAT IS FURNISHED IN THE
PRE-WIRED CONNECTOR MAY CAUSE SERIOUS
DAMAGE OR INTERFERENCE WITH TO ONE OR MORE
IN-CAR SYSTEMS. CAUTION MUST BE USED WHEN
MOUNTING PHONE CRADLES TO THE CONSOLE OR
THE INSTRUMENT PANEL SO THAT NO DAMAGE
OCCURS TO THE HARNESS BEHIND THEM. DO NOT
USE ANY SCREWS THAT ARE LONGER THAN
NECESSARY. DAMAGE CAUSED BY INCORRECT
WIRING OF CELLULAR TELEPHONE OR OTHER
ADD-ON ACCESSORIES IS NOT COVERED BY THE
NEW CAR WARRANTY.
In order to utilize the vehicles pre-wiring, an adapter cable is
available from Saab. The Saab part numbers for these cables
are:
For all 9-5 models: 49-42-058
For all 9-3 models: 50-36-454
Circuits provided in the vehicle 10-pin pre-wired connector:
Pin #1 +30 (unswitched B+ power) from fuse #8 on
9-5/fuse #23 on 9-3 for powering/charging the mobile
telephone battery
Pin #2 +15(switched B+ power) from fuse #27 on
9-5/fuse #17 on 9-3 to turn mobile telephone on/off with
ignition switch.
Pin #3 Pre-wired microphone ground connection
Pin #4 Ground connection (Negative ground)
Pin #5 Mute control to turn off the normal audio system
sound. NOTE: a Negative ground signal from the
telephone is required to activate this feature.
Pin #6 Display lighting
Pin #7 Positive connection for external speaker to
vehicles audio system
Pin #8 Negative connection for external speaker to
vehicles audio system
Pin #9 Microphone positive connection for systems with
high-level output (e.g. Motorola)
Pin #10 Microphone positive connection for systems with
low-level output (e.g. Ericsson, Nokia)
NOTE: Pins 3,9 and, 10 are used on 9-3 SE 5-door and 9-5
models only.
Connector location:
9-3: The pre-wired plug is clipped to the metal bracket
just behind the radio amplifier.
To access: remove the plastic trim panel that makes up
the right side of the center console in the passenger's foot
well. Leave the connector fastened to the bracket to
prevent rattles. Route the cables to the telephone mount,
taking care not to pinch or bind the cables.
9-5: The pre-wired plug is clipped to the HVAC case
directly behind the radio head/ACC control unit.
To access: remove the radio head with correct removal
tools, Saab special tool p/n 84-71-161. Remove the radio
bracket and, pushing from behind, remove the ACC
control panel. The 10-pin plug can be found fastened to
the HVAC case. Leaving the connector fastened to the
case, connect the adapter cable, 49-42-058. Route the
cable to the telephone mount. Care must be taken to
prevent pinching or binding of cable.
9-5 ANTENNA MOUNTING
The 9-5 radio AM/FM antenna is imbedded in the rear window
glass. If a glass mount antenna is used on the rear window, radio
reception may be affected. Drilling of the roof panel, to mount a
surface mount antenna, is not recommended as it could affect
the structural rigidity of the roof panel.
Back to List of Questions
posted by 198.208.2...
No Site Registration is Required to Post - Site Membership is optional (Member Features List), but helps to keep the site online
for all Saabers. If the site helps you, please consider helping the site by becoming a member.