1994-2002 [Subscribe to Daily Digest] |
[Main NG900 & OG93 Bulletin Board | BBFAQ |
Prev by Date | Next by Date | Post Followup ]
Member Login / Signup - Members see fewer ads. - Latest Member Gallery Photos
Re: Noise behind Center Console Posted by REM in Seattle [Email] (#4) [Profile/Gallery] (more from REM in Seattle) on Sun, 11 Oct 2009 22:26:45 In Reply to: Noise behind Center Console, Scott, Sun, 11 Oct 2009 16:05:17 Members do not see ads below this line. - Help Keep This Site Online - Signup |
Cleaning the ACC sensor fan may eliminate the noise. If not, a new ACC sensor and fan unit can be purchased from Saabnet sponsors like http://www.eEuroparts.com and http://www.thesaabsite.com for around $100. Below are the instructions for cleaning the ACC sensor fan.
REM in Seattle
2005 Saab 9-3 Aero Convertible; Steel Gray metallic; 5-speed; 26,000 miles
1998 Saab 900SET; Silver metallic; 5-door; Automatic; 110,000 miles
1984 Saab 900T; Cherry Red; 3-door; 5-speed; 242,000 miles (RIP)
CLEANING THE AUTOMATIC CLIMATE CONTROL (ACC) SENSOR FAN IN THE NG900 AND 9-3
By Rob Mustard (aka REM in Seattle)
Search word: rem_mod
Last updated – 14 July 2009
The ACC sensor fan is located behind the 'bulls-eye' grill next to the right seat heater button. It is a small fan that draws air in through the 'bulls-eye' grill and across a temperature sensor. This allows the ACC to accurately monitor the temperature in the vehicle. The fan will run for a while even after the ignition is turned off. The fan can get dirty or dry of lubricant causing it to make a ticking noise.
The ACC sensor fan assembly can be accessed by removing the ACC unit. Use a thin, flat object like a credit card or putty knife along the edges of the ACC unit to remove it. The ACC sensor fan assembly simply snaps in behind the 'bulls-eye' grill. There is a foam rubber gasket between the grill and the ACC fan assembly sensor to take up any play.
Carefully remove the ACC fan sensor assembly, unplugging the wire harness. Note which side of the fan assembly is in the top position. Also, keep track of the foam rubber gasket.
Using a paintbrush or such, gently clean the fan. A can of compressed air, like that used to clean computer keyboards or cameras, also works well to help blow away the debris.
Apply a little oil or sythetic grease to the fan shaft at the points where it contacts the supporting/bearing surfaces and at the very end of the shaft.
Re-assemble the ACC fan sensor assembly and reinstall. Do not forget the foam rubber gasket and the wiring harness. Some BB users have reported better results if the ACC sensor fan assembly is re-installed upside down from the original position. I suppose this may help equalize the wear on the bearing/support points.
Turn the ignition to the on position and listen carefully to the fan. Make sure it moves freely and that the fan is no longer making any ticking noise.
Re-install the center console cover or ACC unit.
_______________________________________ REM in Seattle Current: 2013 Volvo XC60 R-Design, Rebel Blue, 3.0L 6-cyl turbo, Automatic 2024 MINI Cooper S Convertible, 2.0L 4-cyl turbo, 6-speed manual Former: 2005 Saab 9-3 Aero Convertible, Steel Gray metallic, 2.0L 4-cyl turbo, 5-speed 1998 Saab 900SET 5-door, Silver, 2.0L 4-cyl turbo, Automatic 1991 Alfa Romeo Spider convertible, Alfa Red, 2.0L 4-cyl, 5-speed 1984 Saab 900T 3-door, Red, 2.0L 4-cyl turbo, 5-speed
No Site Registration is Required to Post - Site Membership is optional (Member Features List), but helps to keep the site online
for all Saabers. If the site helps you, please consider helping the site by becoming a member.